Ad Blocker Detected
Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker.
CCNA 3 Scaling Networks Chapter 3 v5 Exam 2016
Quiz-summary
0 of 26 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
Information
CCNA 3 Chapter 3 v5 Exam Answers
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 26 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Average score |
|
Your score |
|
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- Answered
- Review
-
Question 1 of 26
1. Question
1. When a range of ports is being configured for EtherChannel, which mode will configure LACP so that it initiates the EtherChannel negotiation?
Correct
Incorrect
-
Question 2 of 26
2. Question
2. Match the description to the correct command. (Not all options are used.)
Sort elements
- show interfaces fa0/2 etherchannel
- show interfaces port-channel1
- show etherchannel summary
- show etherchannel port-channel
-
This command shows information about the status of the port involved in the Etherchannel.
-
This command shows information about the reliability of the port-channel.
-
This command is used to check what port channels are configured on a switch.
-
This command shows the list of ports involved in the port channel and the time since the ports were bundled.
Correct
Incorrect
-
Question 3 of 26
3. Question
3
What is an advantage of using LACP?Correct
Incorrect
-
Question 4 of 26
4. Question
4
Which command will initiate EtherChannel interface configuration mode?Correct
Incorrect
-
Question 5 of 26
5. Question
5
Launch PT Hide and Save PT
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
What are two reasons why the ping messages that are issued from Laptop0 towards Laptop1 are failing? (Choose two.)Correct
Incorrect
-
Question 6 of 26
6. Question
6
Which three options must match in order to establish an EtherChannel between two directly connected switches? (Choose three.)Correct
Incorrect
-
Question 7 of 26
7. Question
7
Refer to the exhibit. Which switching technology would allow each access layer switch link to be aggregated to provide more bandwidth between each Layer 2 switch and the Layer 3 switch?Correct
Incorrect
-
Question 8 of 26
8. Question
8
Which statement is true regarding the use of PAgP to create EtherChannels?Correct
Incorrect
-
Question 9 of 26
9. Question
9
Which PAgP mode combination will establish an EtherChannel?Correct
Incorrect
-
Question 10 of 26
10. Question
10
What is a best practice to use before beginning an EtherChannel implementation?Correct
Incorrect
-
Question 11 of 26
11. Question
11
Which two protocols are link aggregation protocols? (Choose two.)Correct
Incorrect
-
Question 12 of 26
12. Question
12
Refer to the exhibit. A network administrator has decided that an EtherChannel between ports 0/1 and 0/2 on switches S1 and S2 would help performance. After making the configuration, the administrator notices no performance gain. Based on the output that is shown, what two possible assumptions could a network administrator make? (Choose two.)Correct
Incorrect
-
Question 13 of 26
13. Question
13
Which statement describes an EtherChannel implementation?Correct
Incorrect
-
Question 14 of 26
14. Question
14
When a range of ports is being configured for EtherChannel by the use of PAgP, which mode will form the bundled channel only if the port receives PAgP packets from another device?Correct
Incorrect
-
Question 15 of 26
15. Question
15
As the network administrator you have been asked to implement EtherChannel on the corporate network. What does this configuration consist of?Correct
Incorrect
-
Question 16 of 26
16. Question
16
Refer to the exhibit. The administrator tried to create an EtherChannel between S1 and the other two switches via the commands that are shown, but was unsuccessful. What is the problem?Correct
Incorrect
-
Question 17 of 26
17. Question
17
An EtherChannel link using LACP was formed between two switches, S1 and S2. While verifying the configuration, which mode combination could be utilized on both switches?Correct
Incorrect
-
Question 18 of 26
18. Question
18
What is the most cost-effective method of solving interface congestion that is caused by a high level of traffic between two switches?Correct
Incorrect
-
Question 19 of 26
19. Question
19
Refer to the exhibit. An EtherChannel was configured between switches S1 and S2, but the interfaces do not form an EtherChannel. What is the problem?Correct
Incorrect
-
Question 20 of 26
20. Question
20
Which two load balancing methods can be implemented with EtherChannel technology? (Choose two.)Correct
Incorrect
-
Question 21 of 26
21. Question
21. The trunk link between two 2960 switches has reached its capacity. How can this be addressed in the most economical way?
Correct
Incorrect
-
Question 22 of 26
22. Question
22. A network administrator is configuring an EtherChannel link between switches SW1 and SW2 by using the command SW1(config-if-range)# channel-group 1 mode passive. Which command must be used on SW2 to enable this EtherChannel?
Correct
Incorrect
-
Question 23 of 26
23. Question
23. Which statement describes a characteristic of EtherChannel?
Correct
Incorrect
-
Question 24 of 26
24. Question
24.
Refer to the exhibit. A network administrator issued the show etherchannel summary command on the switch S1. What conclusion can be drawn?
Correct
Incorrect
-
Question 25 of 26
25. Question
25. What are two advantages of using LACP? (Choose two.)
Correct
Incorrect
-
Question 26 of 26
26. Question
26. Which three settings must match in order for switch ports to form an EtherChannel? (Choose three.)
Correct
Incorrect