CCNA 2 R&S Essentials Chapter 5 QUIZ

CCNA 2 R&S Essentials Chapter 5 QUIZ
Rate this post

CCNA 2 R&S Essentials Chapter 5 QUIZ

1 A network administrator enters the following command sequence on a Cisco 3560 switch. What is the purpose of these commands?

Switch(config)# interface gigabitethernet 0/1
Switch(config-if)# no switchport

to shut down the Gi0/1 port
to make the Gi0/1 port a routed port*
to enable the Gi0/1 port as a switch virtual interface
to enable the Gi0/1 port as a bridge virtual interface

2 Which option should be used after the sdm prefer configuration command to enable static routing on Cisco Catalyst 2960 switches?

Switch(config)# sdm prefer qos
Switch(config)# sdm prefer default
Switch(config)# sdm prefer lanbase-routing*
Switch(config)# sdm prefer dual-ipv4-and-ipv6

3 A PC is to access a web server on another network. Which inter-VLAN method will provide the highest bandwidth at Layer 3 and also provide a default gateway for the PC?

router on a stick
multilayer switch with routing enabled*
trunked interface between the router and the switch
multiple physical interfaces on the router, all connected to a Layer 2 switch

4 Fill in the blank. 

The “switchport” parameter can be added to the show interface interface_id command to display the administrative and operational switch interface mode.​

5

Refer to the exhibit. An administrator is troubleshooting a router-on-a-stick network that should have the following requirements:

VLAN ID Network Subnet mask Subinterface Default Gateway
10 172.17.10.0 255.255.255.0 Fa 0/0.10 172.17.10.1
20 172.17.20.0 255.255.255.0 Fa 0/0.20 172.17.20.1
30 172.17.30.0 255.255.255.0 Fa 0/0.30 172.17.30.1

Which two errors can be identified from the show running-config command output from the router? (Choose two.)​​​

There is no IP address that is configured for the router physical interface.
The VLAN ID for VLAN 30 is wrongly configured.​*
A command to configure the router physical interface as a trunk is missing.
The IP address and subnet mask are wrongly configured for VLAN 20.​*
The no shutdown command was not issued on subinterfaces.

6

Refer to the exhibit. Which implementation of inter-VLAN routing does this topology use?

interdomain
router on a stick*
multiple physical interfaces
routing via a multilayer switch

7 Which scalable method must be implemented in order to provide inter-VLAN routing on a switched network with more than 1000 VLANs?

configuring static routes on a Layer 2 switch device
routing traffic internally to a Layer 3 switch device*
connecting each physical router interface to a different physical switch port, with each switch port assigned to a different VLAN
connecting a router interface to a switch port that is configured in trunk mode to route packets between VLANs, with each VLAN assigned to a router subinterface​

8


Refer to the exhibit. What is the cause of the error that is displayed in the configuration of inter-VLAN routing on router CiscoVille?

The gig0/0 interface does not support inter-VLAN routing.
The no shutdown command has not been configured.
The IP address on CiscoVille is incorrect.
The encapsulation dot1Q 20 command has not been configured.​*

9 [button url=”https://dl.dropboxusercontent.com/s/rdqgvbrzc1x2w4r/p9PKTchap5ccna2.pka?dl=1&token_hash=AAHtoN7G_-wo6rDB3P0BtW43LL6ePFsyNlmVWbPgzvF4lw” target=”self” size=”small” color=”dark”]Open the PT Activity.[/button] Perform the tasks in the activity instructions and then answer the question or complete the task.

Which ping command from PC0 to PC1 completes successfully?

ping 192.168.2.2
ping 192.168.2.3*
ping 192.168.2.4
ping 192.168.2.5
ping 192.168.2.6

10 What is the meaning of the number 10 in the encapsulation dot1Q 10 native router subinterface command?​

the interface number
the subinterface number​
the subnet number
the VLAN ID*

11

Refer to the exhibit. A network administrator has configured router CiscoVille with the above commands to provide inter-VLAN routing. What type of port will be required on a switch that is connected to Gi0/0 on router CiscoVille to allow inter-VLAN routing?

routed port
access port
trunk port*
SVI

12

Refer to the exhibit. Inter-VLAN communication between VLAN 10, VLAN 20, and VLAN 30 is not successful. What is the problem?​

The access interfaces do not have IP addresses and each should be configured with an IP address.
The FastEthernet0/2, FastEthernet0/3, and FastEthernet0/4 interfaces are configured as trunk.*
The switch interface FastEthernet0/1 is configured to not negotiate and should be configured to negotiate.​
The switch interfaces FastEthernet0/2, FastEthernet0/3, and FastEthernet0/4 are configured to not negotiate and should be configured to negotiate.​

13

Refer to the exhibit. Fill in the blank. Use dot notation.

PC0 has been assigned the last valid host address in the subnet. The IPv4 address for PC0 will be “_______”.

Correct Answer
192.168.40.6

192.168.40.6.

Leave a Reply

Your email address will not be published. Required fields are marked *

Time limit is exhausted. Please reload the CAPTCHA.

This site uses Akismet to reduce spam. Learn how your comment data is processed.